Coats Industrial


Desert Boots

Sewing thread recommendations for desert boots

Threads and zips used for manufacturing desert boots need to fulfil the following special requirements; resistance to sunlight, UV radiation and severe abrasion; rot proof and colour fast when exposed to external elements like acid rain, chlorinated water, etc.

Coats threads & zips

Coats offer an extensive variety of threads and zips for desert boots. Please see our thread recommendations and zip recommendations below.

Industrial threads and zips for desert boots

Simplify your guide

We can tailor the thread application guide to show you the exact information you require, please select the necessary options from the filter below.

Below are recommended stitch types for this end use item.

Thread and zip illustration for desert boots
Stitch type Machine type Brand
1 301 Back Closing Nylbond More details
2 301 Side seams Nylbond More details
3 301 Veldschoen Brio More details


Coats industrial sewing threads are available in a range of fibre types and finishes, each designed to meet particular customer needs. Please see this comprehensive range below.

  Image of stitch Machine type Stitch type Needle thread Under thread
Brand Tex Ticket Brand Tex Ticket
1 Stitch type 301 - single needle lockstitch Back Closing 301 Nylbond 105 30 Nylbond 105 30
2 Stitch type 301 - single needle lockstitch Side seams 301 Nylbond 105 30 Nylbond 105 30
3 Stitch type 301 - single needle lockstitch Veldschoen 301 Brio 400 1.2mm Brio 500 1.0mm

Key: CE = Closed End; OE = Open End; 2WOE = 2 Way Open End; 2WCE = 2 Way Closed End; X-Form / O-Form

  Opti M Opti RT Opti S
Application   Specials   Specials   Specials
Opening M80 CE - RT10 CE Reversed, Zero-cut toptape ends, HydroF S80 CE HydroS, FlameGuard
M60 CE - RT10 CC Reversed S60 CE Reversed, Reflective, Contrast, Zero-cut toptape ends, Stitch line, Boot curved, Pin bottom stop, Hot melt adhesive, Bi-adhesive, HydroF, FlameGuard
- - - - S60 CC Reversed, Reflective, Contrast, Stitch line, Hot melt adhesive, Bi-adhesive, HydroF, FlameGuard


We can customise any puller for your brand recognition.

Coats Opti Fulda slider for zips Fulda
Coats Opti Werra slider for zips Werra

Care Recommendations

- When attaching the zip, we recommend a minimum gap of 2 mm between the spiral edge and edge of the leather, to ensure the slider runs correctly. This is as per the SATRA recommendation.

- Excessive glue should be removed. Caution should be taken to ensure the glue pots and dispensers are positioned away from the teeth and slider.

- During the soiling out process, the side pushes can be an issue if they press against the slider.

- Attention must be taken with the thickness, width and positioning of the zip guards.

- When the zip goes through the curing tunnel, the slider should be pulled to the top of the boots, and the boots should be laid down with the slider facing upwards.

- Coats have a comprehensive range of flame retardant (FR) zips available: Opti FireFly, Opti FlameMaster, Opti FlameGuard; please contact Coats for more details.

Sewing recommendation for Opti S zips – Whilst sewing, the presser foot can accidently go over the spiral and stitch line and as a consequence this can affect the slider running.

Sewing recommendations for Opti M zips - When applying the zip to the bottom edge, the sewing line needs to be just below the bottom stop. Care must be taken to keep a straight sewing line, because there is a risk of needle breakage if it comes into contact with the teeth.

Since conditions and applications vary considerably in the use of the thread, Coats and its distributors can make no guarantee of results. These recommendations are given in good faith but without warranty or liability on the company or its employees. The thread user should assure herself or himself by preliminarily testing that the thread is suitable for the end use intended. Technical information listed above is based on current averages and should be taken only as indicative.